[1000mp] Maintenance and Repair of the Mark V FP-29 PSU

[Mike Schatzberg]

Hello 1000MP Fans:

Andy, G7LRR,  is checking on the part numbers which were used, and will
report back as soon as he has the info.

I'll post the information as soon as it is received

73 and Happy DXing,

Mike
W2AJI
----- Original Message ----- 
From: "w8gf" <w8gf at aol.com>
To: <1000mp at mailman.qth.net>
Sent: Saturday, January 26, 2008 10:28 AM
Subject: Re: [1000mp] Maintenance and Repair of the Mark V FP-29 PSU


Andy:  What are the part numbers of the ICs replaced in your FP-29?
Mine went South a few months back and I am still trying to figure out
what went wrong.  A replacement  unit cost me nearly $800.00!

73, Gerry (W8GF)



-----Original Message-----
From: Mike Schatzberg <cherokeehillfarm at earthlink.net>
To: 1000mp at mailman.qth.net
Sent: Fri, 25 Jan 2008 9:51 pm
Subject: [1000mp] Maintenance and Repair of the Mark V FP-29 PSU



Hello 1000MP Fans:

I received the email below today, from Andy, G7LRR, regarding his
experience
with the Mark V outboard power supply.
You may want to update your maintenance practice after reading it.

73 and Happy DXing,

Mike
W2AJI


The PSU on the MKV went bang and it was looking like a new unit was
needed
at a cost of £495.00 around $700.00.
Lucky I had friends in the trade that was helpful, as Yaesu UK wanted
£100.00 just to look at it,

In the FP-29 PSU it uses 2 voltages 30volts @ 15 amps and 13.8 @ 5 amps.
With this design it gets very hot and yaesu in their wisdom placed the
cooling fan at the bottom of the unit ¼ inch above this is the CAPS and
transformer around this point is about 600volts DC.

This collects dust like you would not believe, I had a like a cat get a
fluff ball in it which shorted across the caps and diodes solder points
and
taking out 2 main IC.

These are what I call Black box units having no part numbers nor info
in the
drawing from yaesu and made for yaesu only.

These 2 IC alone cost £150.00 around 275 dollars only so they say from
yaesu.

The IC, s are mounted on a board and cover in black resin making it
hard to
fault find and also to see what  the thing does in line.

I had a guy chip all the resin off the IC's and clean them with acid to
find
that the parts are £1.50  $2.00 each cheap as chips really.

Yaesu are making loads of money by doing this and repairing at silly
rates.

Anyway with that said total cost was £45.00 around $75.00.

So all you guys on Mkv with a External PSU take that cover off and blow
it
out with a air bush and get some lacquerer and spay the bottom of the
PCB
this will stop dust making a short and costing you loads.


Cheers All

Andy

G7LRR


______________________________________________________________
1000mp mailing list
Home: http://mailman.qth.net/mailman/listinfo/1000mp
Help: http://mailman.qth.net/mmfaq.html
Post: mailto:1000mp at mailman.qth.net


________________________________________________________________________
More new features than ever.  Check out the new AOL Mail ! -
http://webmail.aol.com
______________________________________________________________
1000mp mailing list
Home: http://mailman.qth.net/mailman/listinfo/1000mp
Help: http://mailman.qth.net/mmfaq.html
Post: mailto:1000mp at mailman.qth.net