[1000mp] roofing filters on a mark v field...

[ON4ADZ]

Noel,

I have decreased the 9.1 setting wiht two numbers, this setting is for me,
with my ears as instruments,the best.

menu 8.4 is set at tuned.

I do mainly contest work mostly rtty mode, the settings I change during
contesting are:  filters  500 or 250 , ipo , or 6 db att.
In ssb mode I use idpt, sift and width settings.


73

Dirk

on4adz



-----Oorspronkelijk bericht-----
Van: 1000mp-bounces at mailman.qth.net
[mailto:1000mp-bounces at mailman.qth.net]Namens NOEL POULIN
Verzonden: donderdag 17 maart 2005 18:31
Aan: All about Yaesu 1000mp
Onderwerp: Re: [1000mp] roofing filters on a mark v field...


Hello Dirk
Well I have done  it.....nice job ....very easy...Thanks for your answer...
NOw I have to do the ohter one, cuz I do have two of them,....
I wonder in the menu 9-1  what is the number after your installation....
I decreases my number by one according to INRAD instructions...
ALso, tell me  if you operate your mark v FLAT or TUNED in the menu 8-4 for
contests working????
Thanks again Dirk
Regards
NOEL ve2ryy
----- Original Message -----
From: "ON4ADZ" <on4adz at pro.tiscali.be>
To: "All about Yaesu 1000mp" <1000mp at mailman.qth.net>
Sent: Thursday, March 17, 2005 11:49
Subject: RE: [1000mp] roofing filters on a mark v field...


> Dear Noel
>
> I have installed the roofing filter in my Mark v model, last october.
>
> Most of the time went to take off the up and lower metal case, with the
> markv you need to take off side panels also.
>
> Soldering can be done , you need :
> - good eye sight
> - enough light : min. 500 lux.
> - steady hands
> - solder iron 20 to 30 watt with a small tip
> Soldering is done in an area with normal components, no smd components.
>
> If you have ever built and soldered a kit you can do it.
>
> Putting in the roofing filter is easy, to put in the 2 nylon stand-off
feet
> push and turn on the same time.
> coax connecting is well explained in the instructions.
>
> If you want I have a picture of the installed filter, answer me directly.
>
> Needed time : disassembling, soldering, building in, reassambling,....
> about  1 hour if all the tools are ready and if you have read the
> instructions twice.
>
> 73
> DIRK
> on4adz
>
>
>
> -----Oorspronkelijk bericht-----
> Van: 1000mp-bounces at mailman.qth.net
> [mailto:1000mp-bounces at mailman.qth.net]Namens NOEL POULIN
> Verzonden: woensdag 16 maart 2005 23:35
> Aan: All about Yaesu 1000mp
> Onderwerp: [1000mp] roofing filters on a mark v field...
>
>
> Hi I wonder how long does it take to intall the roofing filter in a
Field...
> I just received the filter today...and try to figure out ....
> I was told the worst is to solder the 2 #12 wires on the board....
> I would like to know how hard is it to solder these wires.....???and m
aybe
> more infos....
> Thanks again
> NOEL ve2ryy
> ______________________________________________________________
> 1000mp mailing list
> Home: http://mailman.qth.net/mailman/listinfo/1000mp
> Help: http://mailman.qth.net/mmfaq.html
> Post: mailto:1000mp at mailman.qth.net
>
>
> ______________________________________________________________
> 1000mp mailing list
> Home: http://mailman.qth.net/mailman/listinfo/1000mp
> Help: http://mailman.qth.net/mmfaq.html
> Post: mailto:1000mp at mailman.qth.net
>

______________________________________________________________
1000mp mailing list
Home: http://mailman.qth.net/mailman/listinfo/1000mp
Help: http://mailman.qth.net/mmfaq.html
Post: mailto:1000mp at mailman.qth.net